Cork Underlayment Adhesive

$79.00
Product Type: Adhesive
-
+
We Ship throughout the greater u.s.
100% Secure Payment

Premium Cork Underlayment Adhesive

Natural Cork Underlayment Adhesive provides a good bond between cork underlayment and most wood or concrete subfloors.

  • Zero Toxic Emissions
  • Low VOC
  • Fast tack-up — dries in 20 minutes
  • Easy-to-use
  • 4 Gallon Bucket

  • DESCRIPTION: 4 gallon bucket.  1500 Multi-purpose Adhesive: Shaw 1500 is a solvent free, nonflammable, latex based adhesive used for the interior installation of a wide variety of flooring materials. 1500 provides a strong bond, has excellent open time, wet tack and high ultimate strength. Do not use outdoors.

     

    USE TO INSTALL:

    Cork: Use to install natural cork underlayments to approved substrates.

    Sheet Goods: Commercial, felt-back and inlaid sheet vinyl.

    Carpet: Jute, latex unitary, polypropylene (actionbac®), needle punched, polyurethane laminate, attached polyurethane cushion, woven carpet, rubber foam back, all backings designed for the installation of direct glue down carpet, and Shaw approved double-stick installations. *NOTE - Not recommended for use with vinyl back flooring of any kind, LVT/LVP or Shaw broadloom carpet.

    USE OVER: Concrete: above, on or below grade in the absence of excessive moisture and alkali. APA registered plywood underlayment, hardboard, association grade particleboard. NOT recommended over existing vinyl flooring.

    FLOOR PREPARATION: Floor must be clean, level and dry. Remove all foreign substances such as wax, grease, dirt and any substance  or chemical that would interfere with a good bond. Test concrete subfloor for alkalinity (pH of floor should be between 5 and 9). Take corrective measures if concrete surface pH is outside these limits.

    Moisture tests should be performed using an anhydrous calcium chloride test according to ASTM F-1869 test method. Moisture emissions should not exceed 5.0 lbs. per 1000 square feet per 24 hours (2.27 kg/92.9m2/24 hours).

    Relative Humidity readings according to ASTM F-2170 should not exceed (RH) 85%. If both tests are performed the RH test is the qualifying standard. Fill all holes and cracks with a Portland cement based patching compound. Sand high spots, install underlayment grade plywood or particleboard underlayment over tongue and groove flooring to eliminate the possibility of telegraphing.

    For best results, the room, floor covering and adhesive should be between 65°F (18°C) and 95o F (35o C) and at a relative humidity between 30% and 60% for 24 hours before, during and after the installation.

     

    PHYSICAL PROPERTIES

    Base: Synthetic rubber, resin blend

    Appearance: Off-white, smooth, easy to spread mastic

    Working time: 20 - 30 minutes under normal conditions

    Shelf life: One year in unopened container at 70° F (21°C).

    Other features: Solvent-free, non-flammable, freeze/thaw stable to 10° F (-12° C). Anti-microbial–protected.

    CAUTION: DO NOT take internally. If swallowed, DO NOT induce vomiting. Call a physician immediately. KEEP OUT OF REACH OF CHILDREN.

    WARRANTY INFORMATION: This product is covered by a 7 year limited warranty. For information on this limited warranty, please ask your authorized Shaw retailer or contact 1.800.471.7429.

    Cork Direct warrants its products to meet all published specifications and to be free of any and all manufacturing defects. No other warranty is expressed or implied.

    The finish of all CorkDirect tile and plank flooring is warranted not to wear through under normal use at any time during the life of the floor. “Wear-through” is defined as complete finish removal on any amount over 3% of the total installation. This non-transferable warranty applies only to the original purchaser.